1. How to buy BONAD's products? Firstly, please send us an inquiry letter or contact us on Trade Manager. Secondly, we will send you our quotation or PI and design drawing based on your requirements.  Thirdly, you make the deposit payment, we begin the production process.  Then, you make the balance payment, we arrange the shipping process.  Finally, we send you BL and you can pick up your goods at the port. 2. What's your payment terms? BONAD  accept T/T, PAYPAL,WESTER UNION, 3. Are we factory? Yes,we are Factory + trade(intergration),more than 10 years experience on test instruments firld. Of course. You will be very wecolmed to visit our factory, even not for inspecting goods. For any questions, please feel free to contact me. 1. How to buy BONAD's products? Firstly, please send us an inquiry letter or contact us on Trade Manager. Secondly, we will send you our quotation or PI and design drawing based on your requirements.  Thirdly, you make the deposit payment, we begin the production process.  Then, you make the balance payment, we arrange the shipping process.  Finally, we send you BL and you can pick up your goods at the port. 2. What's your payment terms? BONAD  accept T/T, PAYPAL,WESTER UNION, 3. Are we factory? Yes,we are Factory + trade(intergration),more than 10 years experience on test instruments firld. Of course. You will be very wecolmed to visit our factory, even not for inspecting goods. For any questions, please feel free to contact me.
Tapered Roller bearings are
radial thrust rolling bearings with tapered roller. There are two kinds of cone
angle and big cone angle .Small cone angle mainly bear radial direction load
primarily radial and axial loads, often used in pairs, reverse installation,
inner and outer ring can be installed separately, in installation using radial
and axial clearance can be adjusted; Big cone angle mainly bear axial load
primarily of axial and radial load, is generally not used to bear alone the
pure axial load, as to the pair (end with the same relative installation) can
be used to carry pure radial load.
Tapered roller bearings are
widely used in automobile, rolling mill, mining, metallurgy, plastic machinery
and other industries.
Range of size are below:
Single row tapered roller
bearing:
Inner diameter range: 20mm ~
1270mm.
Outer diameter range: 40mm ~
1465mm.
Width: 15mm ~ 240mm.
Double row tapered roller
bearing:
Inner diameter range: 38mm ~
1560mm.
Outer diameter range: 70mm ~
1800mm.
Width: 50mm ~ 460mm.
Four row tapered roller
bearings:
Inner diameter range: 130mm ~
1600mm.
Diameter range: 200mm ~
2000mm.
Width: 150mm ~ 1150mm.
The precision we can produce
P0~P2.
We believe that we can supply the best service and price for your,
hope to make a long-term cooperation with you. If you have any question please
do not hesitate contact with us. We keep warmly welcome you visit us in any
time.
Tapered Roller Bearing,Roller Bearing,Taper Bearing,Tapered Roller LUOYANG AUTO BEARING CO.,LTD , http://www.lyautobearing.com
Product Description
IEC60695-11-5 NEEDLE FLAME TESTER
Needle-flame Tester could be applicable to ignition hazard test, combustibility test of electronic industry, home electronic appliance and materials. This tester specifies a needle-flame test to simulate the effect of a small flame which may result from fault conditions, in order to assess product and material's ignition risk and fire retardance by a simulation technique the fire.
This product is designed and manufactured according to IEC60695-11-5:2004(GB/T5169.5-2008) Fire hazard testing for electric and electronic products-part 2: Test methods- needle-flame test methods.
Needle-flame Tester's crust and important parts are made by Stainless Steel, Sculpt daintily, endure smoke corrupt, high automatism, high reliability of key parts of apparatus, numeric shows. Fixture could be adjusted. Test procedure could be controlled automatically which is convenience and reliable.
Detailed Images
needle burner
the hole Φ 0.5mm ± 0.1mm, outside diameter ≤ Φ 0.9mm, length ≥ 35mm,
Material
stainless steel
burner angle
tilt 45 ° (test) or vertical (adjust the flame height)
Application time
0-999 .9 s ± 0.1s adjustable (normally choose to 30s)
Burning duration
0-999 .9 s ± 0.1s, auto record, manual suspension
flame height
12mm ± 1mm (with a height measurement apparatus)
Burn gas
95% of the butane gas (Pressure:Less than 0.2MP)
temperature measurement range
0 ~ 1000 ºC
flame temperature requirements
from 100 ºC ± 2 ºC 700 ºC ± 3 ºC rise to the timeÂ
in 23.5 seconds ± 1 seconds
Thermocouple
Φ0.5mm (K type)
experimental background
black background
test procedure
automatic control
reference standard
IEC60695 -11-5-2004, GB/T5169.5-2008
inside dimension
0.5 cubic meters, stainless steel chassis
equipment dimensions
1000mm wide × 650mm deep × 1300mm highÂ
power supply
AC220V ± 5%, 50Hz, 0.3KVA
         Â
4. Can we visit your company to inspect the goods?Â
Â
Product Description
IEC60695-11-5 NEEDLE FLAME TESTER
Needle-flame Tester could be applicable to ignition hazard test, combustibility test of electronic industry, home electronic appliance and materials. This tester specifies a needle-flame test to simulate the effect of a small flame which may result from fault conditions, in order to assess product and material's ignition risk and fire retardance by a simulation technique the fire.
This product is designed and manufactured according to IEC60695-11-5:2004(GB/T5169.5-2008) Fire hazard testing for electric and electronic products-part 2: Test methods- needle-flame test methods.
Needle-flame Tester's crust and important parts are made by Stainless Steel, Sculpt daintily, endure smoke corrupt, high automatism, high reliability of key parts of apparatus, numeric shows. Fixture could be adjusted. Test procedure could be controlled automatically which is convenience and reliable.
Detailed Images
needle burner
the hole Φ 0.5mm ± 0.1mm, outside diameter ≤ Φ 0.9mm, length ≥ 35mm,
Material
stainless steel
burner angle
tilt 45 ° (test) or vertical (adjust the flame height)
Application time
0-999 .9 s ± 0.1s adjustable (normally choose to 30s)
Burning duration
0-999 .9 s ± 0.1s, auto record, manual suspension
flame height
12mm ± 1mm (with a height measurement apparatus)
Burn gas
95% of the butane gas (Pressure:Less than 0.2MP)
temperature measurement range
0 ~ 1000 ºC
flame temperature requirements
from 100 ºC ± 2 ºC 700 ºC ± 3 ºC rise to the timeÂ
in 23.5 seconds ± 1 seconds
Thermocouple
Φ0.5mm (K type)
experimental background
black background
test procedure
automatic control
reference standard
IEC60695 -11-5-2004, GB/T5169.5-2008
inside dimension
0.5 cubic meters, stainless steel chassis
equipment dimensions
1000mm wide × 650mm deep × 1300mm highÂ
power supply
AC220V ± 5%, 50Hz, 0.3KVA
         Â
4. Can we visit your company to inspect the goods?Â
Â
IEC60695 Lab Needle Flammability/Flame Materials Testing Machine
Model NO.: BND-ZY
Display: Needle
Control: Manual Control
Weight: 100-500Kg
Power Source: AC220V
Standard: IEC60695 -11-5-2004
Warranty: 1 Year
Brand Name: Bonad
Thermocouple: 0.5mm (K Type)
Application Time: 0-999 .9 S ± 0.1s
Flame Height: 12mm +/-1mm
Burn Gas: 95% of The Butane Gas
Testing: Ignition Hazard Testing
Model: Bnd-Zy
Product Name: Needle Flame Test Equipment
Trademark: BONAD
Transport Package: Carton Case
Specification: 1000mm* 650mm*1300mm
Origin: Shenzhen
HS Code: 9024900000
Model NO.: BND-ZY
Display: Needle
Control: Manual Control
Weight: 100-500Kg
Power Source: AC220V
Standard: IEC60695 -11-5-2004
Warranty: 1 Year
Brand Name: Bonad
Thermocouple: 0.5mm (K Type)
Application Time: 0-999 .9 S ± 0.1s
Flame Height: 12mm +/-1mm
Burn Gas: 95% of The Butane Gas
Testing: Ignition Hazard Testing
Model: Bnd-Zy
Product Name: Needle Flame Test Equipment
Trademark: BONAD
Transport Package: Carton Case
Specification: 1000mm* 650mm*1300mm
Origin: Shenzhen
HS Code: 9024900000
IEC60695 Lab Needle Flammability/Flame Materials Testing Machine
FAQ
IEC60695 Lab Needle Flammability/Flame Materials Testing Machine
FAQ