China drying wire Reuters in most of the country enters the wet season, the number of high-end brand name desiccant dryer series also entered the sales season. Its products are widely used in food, warehousing, electronics, electricity, telecommunications, pharmaceuticals, tobacco, chemicals, printing, military, finance, graphic files, cultural relics and other fields, and are very popular with customers. These high-end dehumidifying and drying equipments have the following features: 1. Super dehumidifying capacity; 2. Air-clearing function, nanometer silver static filter; 3. Simple and fashionable appearance, fresh and refined, fine workmanship; 4. Ultra-quiet operation, minimum Up to 39 decibels, to keep you away from dampness without affecting the rest of your family and your family. 5. It can be applied to a variety of complex work environments. News link: Heat pump desiccant drying equipment The dehumidifying dryer should be cleaned from time to time and kept clean. The dehumidifier should be placed in the center of the room. The air inlet and outlet of a refrigerated dryer must not be obstructed and the air filter should be cleaned. When the ambient temperature is lower than 15°C, the water droplets adhering to the surface of the evaporator will freeze and the dehumidifier will be less effective. If the ambient temperature exceeds 40°C, the pressure in the system will increase to overload the compressor. At this time, the overload protector The line should be cut off or the compressor motor could be damaged. Therefore, the optimum dehumidifier temperature range is 15°C to 40°C. If the humidity in the air is lower than 30%, it is too dry and uncomfortable, so the reliable humidity controller is controlled to maintain the range of 50% to 60%. When using, the doors and windows should be closed as much as possible so that the indoor dehumidification effect can be achieved. The desiccant dryer body should be flat and must not be tilted or traversed to avoid machine malfunction or abnormal noise. When the dehumidifying dryer has excessive water storage capacity to avoid overflowing the soiled floor and must be transported during operation, unplug the power cord and drain the water in the storage tank. After the dehumidifier is moved, it is best to let it rest for four to six hours in advance, and then turn it on. Because the compressor line in the dehumidifier contains cold coal, the cold coal must return to its original position after four to six hours after being moved. Clean the air filter network regularly (about once every two weeks) to maintain the dehumidification, dust removal efficiency and life of the machine. Clean the air filter net to wash with clean water below 40°C; use a detergent to clean it better, wash off the dust, rinse it off with water, and put it back in the body after drying. When cleaning the body, gently wipe with a damp cloth; avoid direct water cleaning, so as not to damage the electrical insulation. Adhesive on the surface of the body can be washed with soap and water, avoid spraying with gasoline, petroleum spirit, solvent or spray insecticide to avoid peeling or discoloration. It is not possible to use thin rods or wire to pick up the inside of the machine to prevent malfunction or danger. When there is a power outage, or when you are not using it for a long time, or when traveling, please unplug the power cord to maintain the life of the machine.
Nosen Spiral Bevel Gearbox has 42 kinds of transmission directions and is used in many mechanical field. Compared to worm gear reducer, our gearbox is of flexible operational capacity and higher transmission torque.efficiency up to 95%. Gear ratio 1:1, 2:1 as our standard, gear box. 2 way,3 way,4 way gearboxes are available. 10 kinds of models for your selection.
NOSEN Spiral bevel right Angle Bevel Gearbox RN series: Spiral Bevel Gearbox Spiral Bevel Gearbox,Right Angle Spiral Bevel Gearbox,Spiral Bevel Worm Gear Gearbox,Helical Hypoid Spiral Bevel Gearbox Dongguan Nosen M&E Technology Co., Ltd. , http://www.screwjack.cc
Configurations: Bevel Gear 90°structure.
Ratio: 1:1.2:1.3:1.4:1.5:1.
Range of speed: 10-1500RPM
Input torque:11.6-5713NM;
Input power:0.1-335KW;
Input shaft: 1 input 1 output,1 input 2 output,1 input 3 output,
Rotate direction: clockwise/anticlockwise, 42 kinds of rotate directions.
Noise level:<80db;transmission efficiency 95%
environment temperature:-20℃-+80℃